LCD Display M5 User Manual
1, Exterior Parameters
Casing Material: ABS
Display Material: High Hardness Acrylic (the same hardness value as tempered glass)
Front View
Side View
31.8mm handlebar ring diameter options: 22.2mm /25.4mm / 28.6mm
1. Operating Voltage and Connections
a. Operating Voltage: DC24V / 36V / 48V / 60V / 64V by display setting. Other operating voltage can be customized.
b. Connections:
A. Standard Cabling Connection
Standard Connector Sequence Table
Sequence No. | Wire Colour | Functions |
1 | Brown（VCC） | Display Power Cable |
2 | Green（RX） | Data Receiving Cable |
3 | Black（GND） | Display Ground Cable |
4 | Orange（K） | Power Control Cable |
5 | White（TX） | Data Sending Cable |
The extended cable will be waterproof type, whose color cannot be seen from exterior.
Functions:
Display
Speed Display, PAS Level Display, Battery Level Display,
Error Indication, Total Mileage, Single Mileage, Single Running Time
Light Signal
Control and Settings
Power Switch, Front Light Control, 6km/h Inching Control, Wheel Diameter Setting, Top Speed Setting, Auto-Hibernation Interval, Backlight Brightness Setting, Voltage Level Setting
Communications Protocol:UART
Display Readings (display at start for 1 second)
Display Details
3.1 Light
Turned on manually or environment-sensed (requires light-sensitive support)
3.2 Battery Level
3.3 Multi-Functions Display
Total Mileage: ODO
Single Mileage: TRIP A
Single Mileage: TRIP B
Current Voltage VOL
Operating Current: CUR
Display Booting Time: TM
3.4 Riding Mode
Walk: Walking Boost
Cruise: Constant Speed Cruise
PAS: Power Assist Level (0-9 Adjustable)
- 5 Speed Display
Maximum Speed: MAX
Average Speed: AVG
Measuring Unit: MPH or KM/H
The display will calculate the actual travelling speed based on the wheel diameter and signal data.
3.6 Vehicle Status
Error Code and Indications
Error Code (decimal) | Indications | Note |
0 | Normal |
|
1 | Reserved |
|
2 | Brake |
|
3 | PAS Sensor Failure (riding mark) | Not Realized |
4 | 6km/h Cruise |
|
5 | Real-Time Cruise |
|
6 | Low Battery |
|
7 | Motor Failure |
|
8 | Throttle Failure |
|
9 | Controller Failure |
|
10 | Communications Receiving Failure |
|
11 | Communications Sending Failure |
|
12 | BMS Communications Failure |
|
13 | Light Failure |
|
3.7 Settings
P01: Backlight Brightness (1: darkest; 3: brightest)
P02: Mileage Unit (0: KM; 1: MILE)
P03: Voltage Class: 24V / 36V (default) / 48V
P04: Hibernation Time (0: never, other figures refer to the hibernation time) Unit: minute
P05: PAS Level – 0/3 Gear Mode 1/5 Gear Mode
P06: Wheel Diameter Unit: inch Precision: 0.1
* To get accurate speed display, this parameter should be correct.
P07: Magnet Steel Number for Speed Test Range: 1-100
* To get accurate speed display, this parameter should be correct.
Gearless Motor: the value is the magnet steel number.
Geared Motor: the reduction-gear ratio is required. The value = magnet steel number*reduction-gear ratio.
For example, magnet steel number is 20, reduction-gear ratio is 4.3. The value input is: 86=20×4.3
P08: Speed Limit
Range: 0-100km/h, parameter 100 indicates no speed limit.
This parameter limits the max. speed of the vehicle.
For example, input value 25 means the max. speed is 25km/h, the vehicle travelling speed can only reach the preset value.
Deviation: ±1km/h (applies to both PAS and throttle mode).
Note: The above-mentioned values are measured by metric unit (kilometers). When the measuring unit is switched to imperial unit (mile), the speed value displayed on the panel will be automatically switched to corresponding imperial unit, however the speed limit value in the imperial unit interface won’t change accordingly.
IMPORTANT: P09-P15 only works under communications mode.
P09: Zero / Non-zero Start Setting:
0: Zero Start
1: Non-zero Start
P10: Drive Mode Setting
0: Power Drive – The specific gear of the assist drive decides the assist power value. In this status the handlebar does not work.
1: Electric Drive – The vehicle is driven by the handlebar. In this status the power gear does not work.
2: Power Drive + Electric Drive – Electric drive does not work in zero-start status.
P11: PAS Sensibility Range: 1-24
P12: Assist Power Intensity Range: 0-5
P13: Power Magnet Steel Number: 5 / 8 / 12pcs
P14: Current Limit Value: 12A by default; Range: 1-20A
P15: Unspecified
P16: ODO Zero-Out: Long press the upper key for 5 seconds and ODO will zero out.
- Keys
Arrangement of keys on the panel:
Introduction of Keys
Key operations involve short press, long press and long press of combination keys.
Short press is used for short/frequent operations as:
- Short press the two keys to change assist power/speed during riding.
- Short press this key to switch the readings in the multi-function display section.
Long press on a single key is used to switch mode/on/off status.
Long press on combination keys to set parameters, which can avoid misoperations (short press on combination keys is disabled, for it’s easy to induce misoperation and hard to manipulate).
Detailed Instructions
- Change Assist Power/ Electric Gear
In assist power mode
- Short press , assist power +1.
- Short press , assist power -1.
- Switch Speed Display
Long press + to switch speed display type.
- Enable / Disable 6km/h cruise, set real-time cruise and turn on/off the lights
When the vehicle is parked, long press to enter 6km/h cruise mode. When the vehicle is travelling, long press to enter real-time cruise mode.
Long press to exit the cruise mode when the vehicle is in cruise mode.
Long press to turn on/off the lights.
- Turn on/off the LCD Panel
When the display panel is operating, long press and it will be turned off, otherwise it will be turned on.
- Switch Displayed Readings in Multi-Functions Section
Short press to switch readings shown in the multi-functions section.
- Set Parameters
Long press +to enter the setting interface. Customizable parameters include:
Wheel Diameter (unit: inch);
Magnet Steel Number;
Backlight Brightness;
Low Voltage Threshold (refer to setting: P01-P14)
In the setting interface, short press or to add/minus value to the parameter, which will blink after modified. After selecting the parameter that needs to be set,
- a. Long press to save the current value, and the parameter will stop blinking;
- Short press to switch to the next parameter and the previously set value will be saved at the same time.
- Press +to exit the setting and save the parameters. Without this operation, the system will automatically exit and save the modified parameters after 10 seconds.
Note: Due to product upgrade, the product you purchased may be slightly different from the descriptions in this user manual, and this won’t affect normal usage.
https://akezebikes.com/
Hi, I bought the 20*40 s2 jaguar model
I was just wondering how to proper set the odometer to get the best performance of the bike?!
Thank you
I got the M5 display and it wants a password I never got a password when I got the display can you help me
When I turn it on I think it’s asking for password or number. Can you help me please
PAS doesn’t mean PASSWORD it means the PAS Level where PAS stands for Pedal ASsist.
Не снимается ограничение 25 км ч .. не работает акселератор, когда дохожу до R08 + не кликабелен
The password is 6666